TiePie Handyscope HS4 DIFF, 4-Channel, 16Bit PC Differential Oscilloscope Series
The Handyscope HS4 DIFF is a 4-channel differential USB oscilloscope with a maximum sampling speed of 50MSa/s and 128kSa memory per channel. The digital storage oscilloscope is delivered with a complete measurement software package that offers all you need for your measurement applications.
The Handyscope HS4 DIFF oscilloscope features a user selectable 12 bit, 14 bit or 16 bit resolution, 200mV to 80V full scale input ranges each and 128kSa record length per channel.
The Handyscope HS4 DIFF is available in several variants with different maximum sampling rates on all four channels simultaneously: 5MSa/s, 10MSa/s, 25MSa/s or 50MSa/s
The variants differ in sampling rate and warranty period. (Please select when ordering!)
Differential inputs
The Handyscope HS4 DIFF features four isolated differential input channels. This makes it the ideal instrument to perform measurements in high voltage and mains circuits, amplifiers, switch mode power supplies, power inverters etc. No more risk of creating short circuits through your oscilloscope!
A differential input is not referenced to ground, but both sides of the input are "floating". It is therefore possible to connect one side of the input to one point in the circuit and the other side of the input to the other point in the circuit and measure the voltage difference directly.
Advantages of a differential input:
- No possibility to create a short circuit to ground through the oscilloscope.
- Only one channel is used to measure the signal.
- More accurate measurement, since only one channel introduces a measurement error.
- The Common Mode Rejection Ratio of a differential input is high. If both points have a relative high voltage, but the voltage difference between the two points is small, the voltage difference can be measured in a low input range, resulting in a high resolution.
There are various applications for oscilloscopes with differential inputs:
Power systems
One application for oscilloscopes with differential inputs is measurements in (switch mode) power supplies, motor drives, frequency inverters. The high common mode voltages and low voltage differences make an oscilloscope with differential inputs the ideal measuring instrument. It also reduces the risk of creating short circuits, resulting in damaged circuits and/or measuring instruments.
Communication buses
Oscilloscopes with differential inputs can also be used very well when measuring at (high speed) digital communication buses like e.g. USB and CAN.
To improve signal integrity, such buses use two differential signal lines and a common ground line. The two signal lines transport the same signal, with the difference that they are each others inverse. This reduces the effect of external influences, since most external disturbances are additive and cause the same offset error in both signal lines. The voltage difference will remain the same, so the actual signal is not affected. To measure the actual signal, a differential input is required.
Audio systems
Another application for oscilloscopes with differential inputs is measuring in professional audio systems. Just as for the digital buses described above, also in professional audio systems two signal lines and a ground line are used to improve the signal integrity (here called "balanced").
The Handyscope HS4 DIFF is supplied among others with a set of four DP-DA10 differential 1:10 attenuators which allow to measure voltages up to 300V.
Fast Continuous Streaming
The Handyscope HS4 DIFF is a high-performance 50MSa/s USB oscilloscope that can be used as a multimeter, spectrum analyzer, data logger/transient recorder or protocol analyzer via the accompanying Windows software. To operate, the oscilloscope must be connected to the USB interface of a PC and the software must be loaded. The device is powered via the USB interface, but can also be connected to an optional external power supply if the computer's USB interface does not provide enough power.
Besides measuring in block mode as oscilloscope, the Handyscope HS4 DIFF is also capable of performing continuous streaming measurements as a data logger. This will create a continuous uninterrupted data stream to the computer. The data can then be displayed on the screen and/or saved to disk.
Combining multiple Handyscope HS4 DIFFs
When one Handyscope HS4 DIFF does not offer enough input channels, the Handyscope HS4 DIFF can be coupled to one or more other instruments. This allows to make a combined instrument which will enable simultaneous measuring on all channels of all combined instruments.
Optional accessories:
- Measure lead TP-C812B, 2m long
- Measure lead TP-C1812B, 3m long
- Rubber protection boot
- and more...
Technical data:
For detailed specifications please download the data sheet:
| Number of input channels: |
4 analog |
| Ch1, Ch2, Ch3, Ch4: |
Isolated BNC, female |
| Type: |
Differential |
| Resolution: |
User selectable in software |
| Native: |
12 bit |
| Enhanced: |
14, 16 bit |
| Accuracy: |
0.3% of full scale ±1 LSB |
| Noise: |
135µVrms (200mV range, 12 bit, 50MSa/s)
50µVrms (200mV range, 16 bit, 195kSa/s) |
| Ranges (Full scale): |
±200mV
±400mV
±800mV |
±2V
±4V
±8V |
±20V
±40V
±80V |
| Coupling: |
AC/DC |
| Impedance: |
2 MOhm / 40pF |
| Maximum input voltage (in all ranges): |
±200V (DC + AC peak < 10kHz)
with 1:10 attenuator ±300V (DC + AC peak <10kHz) |
|
Maximum Common Mode voltage:
|
200mV to 800mV ranges: 2V
2V to 8V ranges: 20V
20V to 80V ranges: 200V |
| Common Mode Rejection Ratio: |
-48dB |
| Bandwidth (-3dB): |
DC to 50MHz maximum |
| AC coupling cut off frequency (-3dB): |
1Hz |
| Channel Isolation: |
500V |
| Channel Separation: |
-80dB |
| |
| Maximum sampling rate: |
HS4 DIFF-50 |
HS4 DIFF-25 |
HS4 DIFF-10 |
HS4 DIFF-5 |
| 12 bit |
50MSa/s |
25MSa/s |
10MSa/s |
5MSa/s |
| 14 bit |
3.125MSa/s |
3.125MSa/s |
3.125MSa/s |
3.125MSa/s |
| 16 bit |
195.3kSa/s |
195.3kSa/s |
195.3kSa/s |
195.3kSa/s |
| |
| Maximum streaming rate: |
HS4 DIFF-50 |
HS4 DIFF-25 |
HS4 DIFF-10 |
HS4 DIFF-5 |
| 12 bit |
500kSa/s |
250kSa/s |
100kSa/s |
50kSa/s |
| 14 bit |
480.8kSa/s |
250kSa/s |
99.2kSa/s |
50kSa/s |
| 16 bit |
195.3kSa/s |
195.3kSa/s |
97.7kSa/s |
48.8kSa/s |
| |
| Sampling clock source |
|
| Internal: |
Quartz |
| Accuracy: |
±0.01% |
| Stability: |
±100ppm over -40°C to +85°C |
| Time base aging: |
±5ppm/year |
| External: |
On extension connector |
| Voltage: |
3.3V TTL, 5V TTL tolerant |
| Frequency range: |
95MHz to 105MHz |
| |
| Memory: |
128kSa per channel |
| |
| Trigger |
|
| System: |
Digital, 2 levels |
| Source: |
CH1, CH2, CH3, CH4, OR, digital external |
| Trigger modes: |
Rising edge, Falling edge
Inside window, Outside window |
| Level adjustment: |
0 to 100% of full scale |
| Hysteresis adjustment: |
0 to 100% of full scale |
| Resolution: |
0.025% (12 bits) |
| Pre trigger: |
0 to 131071 samples, 1 sample resolution |
| Post trigger: |
0 to 131071 samples, 1 sample resolution |
| Trigger hold-off: |
0 to 1048576 samples, 1 sample resolution |
| Digital external trigger |
|
| Input: |
Extension connector |
| Range: |
0 to 3.3V (5V max) |
| Coupling: |
DC |
| Interface: |
USB 2.0 High Speed (480Mbit/s); (USB 1.1 Full Speed (12Mbit/s) and USB 3.0 compatible) |
| Power from USB port: |
500mA max (2.5W max) |
| Power via external power input / extension connector: |
1500mA max (7.5W max) |
| Minimum voltage: |
4.5VDC
|
| Maximum voltage: |
14VDC
|
| Instrument height: |
25mm |
| Instrument length: |
170mm |
| Instrument width: |
140mm |
| Cord length: |
1.8m |
| Weight: |
460g |
| Channel 1...4: |
Isolated BNC, female |
| USB: |
fixed cable with USB 2.0 and USB 1.1 type A connector |
| Extension connector: |
D-sub 25 pins female |
| PC I/O connection: |
USB 2.0 High Speed (480Mbit/s); (USB 1.1 Full Speed (12Mbit/s) and USB 3.0 compatible) |
| Operating System: |
Windows 10 / 11 and Linux (via libtiepie-hw SDK) |
| Ambient temperature: |
0 to +55°C |
| Relative humidity: |
10 to 90%, non condensing |
| Ambient temperature: |
-20 to +70°C |
| Relative humidity: |
5 to 95%, non condensing |
| CE mark compliance: |
Yes |
| RoHS: |
Yes |
| Convenient carrying case |
|
| Instrument: |
Handyscope HS4 DIFF |
| Measure leads: |
4 x Measure lead TP-C812B, BNC -> 4 mm banana plug |
| Accessories: |
4 x Differential attenuator TP-DA10
external power cable for second USB port |
| Software: |
Windows 10 / 11, via website |
| Drivers: |
Windows 10 / 11, via website |
| Software Development Kit: |
for Windows 10 / 11 and Linux, via website |
| Manual: |
instrument manual and software user's manuals
color printed on paper and digital, via website |
| Total package weight: |
Approx. 3kg |
Product safety information
Manufacturer information:
TiePie
Koperslagersstraat 37
SNEEK, Niederlande, 8601 WL
contact@tiepie.nl
| Item information |
Value |
| Shipping weight: |
3,00 kg
|
Manufacturer Information
TiePie
Koperslagersstraat 37
8601 WL SNEEK
Niederlande
contact@tiepie.nl
